SX-80 type plasma spraying equipment (thermal spraying rapid tooling)
spraying equipment
1, SX-80 type plasma spraying system
Plasma spraying system structure
SX-80 type plasma spraying equipment configuration is introduced:
SX-80 type plasma besmear equipment is a introduction absorbs the PT-A3000 and METCO-9 M of plasma spraying equipment based on the successful development, the overall level of equipment and METCO-9 M quite. The equipment includes: (1) the main source (2) (3) (4) to transfer control box for powder spray gun (5) of the heat exchanger
1, SX-80 D Lord power supply
Silicon controlled rectifier, maximum input power 105 KW, temporary load rate was 100%; Maximum output power 80 KW, in the power grid volatility plus or minus 15% conditions, can work normally, current fluctuating range: degree is obtai-plus or minus 2%; Overall size: 1200 mm (long) x 800 mm (wide) x 900 mm (high), weight of about 1000 Kg
2, SX-80 ZJX connecting box
The spray system connecting center, it the power, control cabinets, heat exchangers, spray gun together. The equipped with high-frequency ignition, water and gas path alarm device. The mobile, water cable length for 5 m (standard). Overall size: 750 mm (long) x 360 mm (wide) x 1700 mm (high), weight about 35 kg
3, SX-80 K control cabinet
The whole equipment control center. Single-phase 220 V, 1 KW; Float flowmeter with; Current, voltage digital display, automatic and manual and economic operation of three way to work. Has the alarm or fault display function, general alarm conditions as follows: when the main, auxiliary gas pressure < 0.3 MPa or main gas flow < 30 L/min; When water temperature > 50 ℃ or water flow < 8 L/min. Overall size: 610 mm (long) x 450 mm (wide) x 1700 mm (high), weight: about 60 kg
SX-80 K plasma control cabinet
4, SX-80 F to feed powder device
Offer one a double barrel to feed powder device. Can send powder size range: 5 ~ 200 μ m; Send powder repeat error less than plus or minus 1%. Two rolls of can also send powder, send powder rate 20 ~ 150 g/min. Overall size: 450 mm (long) x 360 mm (wide) x 985 mm (high), about 30 kg weight
SX-80 F to feed powder device
5, SX-80 Q spray gun
Can provide copy METCO 9 MB spray gun, work for the argon or nitrogen qi, auxiliary gas for the hydrogen. Working current: 100 ~ 800 A, working voltage: Ar + H2 as 50 ~ 75 V, N2 + H2 for 50 ~ 80 V. 1 copy 9 MB machine with a gun, 2 copy 9 MB hand gun, 3 working hole gun, and provide the following parts for gun: GH, G, GP, GE type wards, send powder and cooling air jet plane, water cable, electrode head, insulators, seals, special tools, etc. Can also provide copy F4 spray gun (copy machine gun, copy with F4 F4 hand gun) and for spray gun provide the following parts: water cable, nozzle, electrode head, send powder frame, the mouth to feed powder, sealing ring, special tools, etc.
6, SX-80 R heat exchanger
There are two kinds of heat exchanger for selection
(1) water pump type heat exchanger, points inside and outside cycle. Inner circulation distilled water cooling spray gun, external loop (water) cooling distilled water, using imported water pump; Cooling capacity: 20000, calories/h, equipment power 8 KW. Water pump pressure: 0.8 MPa, the flow of water: 8 ~ 20 litres/points, water temperature regulation scope: 20 ~ 38 ℃ (imports). Overall size: 1300 mm (long) x 80 mm (wide) x1000mm (high), weight of about 200 kg
(2) freon refrigeration type heat exchanger, the compressor, water pump, heat exchanger are imported components, cooling capacity: 25000 calories/h, equipment power 13 KW. Water pump pressure: 0.8 MPa, the flow of water: 8 ~ 20 litres/points, water temperature regulation scope: 10 ~ 28 ℃ (imports). Overall size: 1800 mm (long) x 1800 mm (wide) x 1000 mm (high), weight of about 800 kg
